Floral bamboo veneer side tables
Floral bamboo veneer side tables
Sakura table
Inspired by Jason Horvath's Sakura table from Uhuru.
Last year I fell in love with Jason Horvath’s Sakura table from Uhuru. It was out of my price range, so I decided to make my own version using some bamboo veneer a friend gave me and two Ikea Lack tables I got on Craigslist. Aiming for an organic floral design, I used photos of gerber daisies and cosmos to create my patterns. Btw: This treatment would also look great on many other types of painted furniture. How about a 70s geometric pattern on a boring cabinet? P.S. Thanks for your patience and words of encouragement this week. It took me a while to scrape off the old glue and summon the will to try again.

How to make bamboo veneered side tables

Supplies
  • 2 black Ikea Lack side tables
  • large sheets of newsprint or butcher paper
  • paper-backed bamboo veneer (see step #8 for more info)
  • Amazing Goop household contact adhesive and sealant (I know from experience that wood glue doesn’t work.)
  • photos of flowers
  • removable double-sided tape
  • fine sandpaper
  • polyurethane (I used an 8oz. can of Minwax fast-drying polyurethane in clear semi-gloss)
  • masking tape or painter’s tape
Tools
  • Tracer projector
  • pencil and mars plastic eraser
  • ruler
  • tape measure
  • kitchen shears
  • scissors
  • craft knife/self-healing mat
  • artist clipboard (optional)
  • foam paintbrush
dscf3841
1. First, find photos of flowers you want to use (or draw your own freehand).
Click here to download the images I used.
dscf3813
2. Draw a rough sketch of your design.
dscf3815
3. Measure your tables and make sure your paper is going to be big enough for your design.
dscf3834
4. Clip a sheet of paper to the clipboard and lean it against the wall. Place your image under the projector and aim it at the clipboard. (You could tape the sheet of paper to the wall instead, but the clipboard provides a smoother surface for tracing.) Measure the projection and adjust the distance of the projector from the wall until you achieve the right size flower. This cosmo is 18 inches in diameter.
dscf3836
5. Trace the outline of the flower, then cut it out. I found using a craft knife to be faster than scissors. Use whatever tool you’re more comfortable with.
dscf3838
6. Tape the flower to the table to visualize your pattern and decide the size of your next flower.
dscf3845
7. Repeat steps 4 — 6 for each additional flower. Make sure the tables look good from every angle. (I decided against the small flower in the end.)
dscf3850
8. The veneer I used is from Moso Veneer Products. Call the phone number on their website to place an order. As of this writing, it’s $2 per square foot, sold in 4- by 8-foot sheets. That’s way too much for this project, but I can think of 101 uses for the leftovers. Can’t you?
dscf3859
9. Draw a line in each flower where the edge of the table is. Line up this line with the grain of the veneer. Keep the veneer grain consistent throughout your project. Then tape each pattern to the veneer and trace it with a pencil.
dscf3853
10. Cut around the outside edge to create a smaller, less unwieldy piece to work with.
dscf3855
11. Cut it out the shape with kitchen shears (or other heavy-duty scissors). You may want to smooth out some of the sharp curves as you cut to make it easier to cut out.
dscf3857
12. Use a heavy-duty craft knife and a self-healing mat to cut out each center. This is the hardest part of the entire project.
dscf3860
13. Using a ruler, mark and trim off the pieces that will be adhered to the sides of the tables.
dscf3862
14. For the flower that crosses over the two tables, cut it in half along the edge. Then trace and cut a duplicate of each piece. These will be adhered to the sides of the tables.
15. Erase all the visible pencil marks, then lightly sand the jagged edges of every piece of veneer you’ve cut.
dscf3870
16. Using a ruler and pencil, mark and trim off excess pieces. If you have any pieces that extend from the side of the table to the leg, cut at the seam so the leg will still be removable.
dscf3863
17. Paint a thin coat of polyurethane on the top and sides of all the pieces. Let dry three hours. Lightly sand, then apply a second coat. Let dry overnight.
dscf3876
18. Apply a thin layer of glue on the back of one piece at a time. Cover the entire surface. Turn it over and place the piece on your table. Press down.
dscf3877
19. Stack a couple of heavy books on top until the glue cures. Tape the side pieces down with masking tape or painter’s tape.
dscf3885
20. Remove the tape and books a few hours later. The glue will fully cure in 48 to 72 hours.